Lattissima Touch

Please follow the instructions below or watch the video.

When unpacking the machine, remove the plastic film and dispose from machine panels, and both left grid and right grid.

Remove the capsule container, drip tray and water tank. Adjust the cable length and store the excess in the cable guide under the machine.

Place machine in upright position and plug machine directly into 220 volt power outlet.

The water tank can be carried by its cover.

Rinse the water tank before filling with potable water up to maximum level.

Switch the machine on. For the first 2 seconds, the automatic power off and water hardness setting are indicated with steady light.

Place a container under coffee outlet and press the Lungo button. Repeat three times.

Disassemble the Rapid Cappuccino System (R.C.S.) and clean all 6 components in the upper level of your dishwasher. In case a dishwater is not available refer to the «Hand Washing of Rapid Cappuccino System (R.C.S.)» section.

Lift the lever completely and insert the capsule.

Close the lever and place a cup under the coffee outlet.

Press the Ristretto (25 ml), Espresso (40 ml) or the Lungo (110 ml) button. Preparation will stop automatically. To stop the coffee flow or top up your coffee, press again.

Take the cup. Lift and close the lever to eject the capsule into the used capsule container.

Please follow the instructions below or watch the video.

Fill the milk container with your desired quantity of milk. Note: when the milk container is empty, before refilling, thoroughly rinse it and the milk aspiration tube with potable water.

Close the milk container.

Open the steam connector door by sliding it to the right.

Connect the Rapid Cappuccino System to the machine.

Machine heats up for approximately 15 seconds (blinking lights).

Lift the lever completely and insert the capsule. Note: only for Cappuccino or Latte Macchiato. Skip this step when preparing a warm milk froth only.

Close the lever, place a Cappuccino cup or a Latte Macchiato glass under the coffee outlet and adjust milk spout position by lifting it up to the right level.

Adjust the milk froth regulator knob according to the desired volume of froth. Note: do not overturn the milk froth regulator. Overturned position is for inserting/removing the milk froth regulator for cleaning.

Press the Cappuccino, Latte Macchiato button or Warm Milk Froth button.

At the end of the preparation, the CLEAN shines orange. Note: Rinse the milk system after each use.

Lift and close the lever to eject the capsule into the used capsule container. Place a container under milk spout.

Press and hold the "CLEAN" button until machine stops pumping automatically. Rinsing process lasts approximately 16 seconds. "CLEAN" blinks. Milk system rinsing process will start. Hot water combined with steam will flow through the milk spout.

When the rinsing process is finished, the "CLEAN" alert is resumed.

Disconnect the R.C.S. from machine and place it immediately in the refrigerator. Close the machine steam connector door.

Every two days, disassemble the Rapid Cappuccino System, and clean all components in the upper side of your dishwasher. In case a dishwasher is not available, refer to Hand washing of Rapid Cappuccino System (R.C.S.) section.

Please follow the instructions below or watch the video.

Touch and hold the Ristretto, Espresso or Lungo button for at least 3 seconds to enter the programming mode. Brewing will start. Button blinks fast: programming mode.

Release button when desired volume is reached.

Button will blink 3 times to confirm the new volume. The volume is now stored for the next coffee preparation.

Touch and hold Cappuccino, Latte Macchiato or Warm Milk Froth Button for at least 3 seconds. Milk frothing will start.
Button blinks fast: programming mode. Note: please refer to "Factory Settings" section for minimum and maximum programmable quantities.

Release button when desired milk froth volume is reached.
Button still blinks fast: programming mode.
(Cappuccino/Latte Macchiato) When programming the Warm Milk Froth beverage, the programming ends here.

Touch and hold the same button. Brewing will start. Release button when desired coffee volume is reached. Recipe volume is now stored for the next preparations. Button blinks 3 times to confirm the new recipe volume.
Note: the milk froth volume depends on the kind of milk that is used, its temperature and the position of the milk regulator knob. Rotate the SELECT dial to the drink & press the SELECT dial to adjust drink.

Switch the machine ON. NOTE: Remove milk jug.

Press the Latte Macchiato and Warm Milk Froth buttons simultaneously for 3 seconds to enter Menu mode; Descaling and clean alerts will start blinking.

Touch in a single continuous movement the following buttons:
1. Warm Milk Froth
2. Cappuccino
3. Latte Macchiato
4. Lungo
5. Espresso
6. Ristretto

The Warm Milk Froth button blinks to indicate reset mode. Press it to confirm. All buttons will blink 3 times: all cup volumes are reset.

The machine will exit out of menu mode automatically and will return to ready mode.

Switch on the machine. Note: remove milk jug.

Remove the water tank. Close the lever to eject any remaining capsule. Place a container under the coffee outlet.

Press the Latte Macchiato and Warm Milk Froth buttons simultaneously for 3 seconds to enter Menu mode: the Descaling and clean alerts will start blinking. Note: the Menu mode will exit automatically after 30 seconds if no actions are performed, or can be exited manually by pressing the Latte Macchiatto and Warm milk froth buttons simultaneously for 3 seconds.

Touch in a single continuous movement the following buttons:
1. Cappuccino
2. Espresso

The Warm Milk Froth button will blink for confirmation. Once pressed, the emptying mode will start. The coffee buttons will blink alternately: emptying mode in progress.

When the process is finished, the machine switches off automatically. Note: appliance will be blocked for approximately 10 minutes after emptying.

Remove the milk container lid and unplug the milk aspiration tube.

Remove the milk froth regulator knob by turning it to and pulling it up.

Unlock and remove the Rapid Cappuccino System connector by turning it from (BLOCKED) to (UNBLOCKED) and pulling it off.

Remove the milk spout by pulling it off.

Disassemble the Rapid Cappuccino System. Refer to "Assembling/Disassembling of Rapid Cappuccino section system (R.C.S.)".

Rinse away carefully any milk residue with potable water.

Soak all components in warm water (approximately 40° C/104° F) together with soap detergent for at least 30 minutes.

Rinse with potable water and dry them with a clean damp cloth.

Please follow the instructions below or watch the video.

Remove drip tray, capsule container. Empty and rinse. Remove water tank. Empty and rinse it before filling with fresh potable water.

Lift and close the lever to eject the capsule into the used capsule container. Place a container under coffee outlet and press the Lungo button to rinse.

Clean the machine surface using a clean damp cloth.

Descale the machine when descaling alert shines orange in ready mode. Please follow the instructions below to descale or watch the video.

Lift and close the lever to eject any capsules in the used capsule container.

Empty the drip tray and the used capsules container. Fill the water tank with 100 ml/3.38oz of Nespresso descaling agent and 500 ml of water.

Open the descaling pipe storage door. Plug the descaling pipe into the steam connector of machine.

The machine will enter the descaling mode. The descaling alert will blink orange during the entire descaling process. The Warm Milk Froth button will shine white.

Place a container with a minimum 1 litre capacity under both the coffee outlet and under the descaling pipe nozzle.

Press the Warm Milk Froth button. Descaling solution will flow alternately through the coffee outlet, descaling pipe and drip tray.

When the descaling cycle is finished (water tank runs empty), the Warm Milk Froth button will shine.

Empty the used capsule container and drip tray. Rinse out and fill the water tank with fresh potable water up to level MAX.

Press the Warm Milk Froth button again. The rinsing cycle continues through the coffee outlet, descaling pipe and drip tray until the water tank turns empty.

Once the rinsing process is finished, the machine switches off. Remove and store descaling pipe. Empty drip tray and used capsules container. Fill water tank with fresh potable water.

Clean the machine using a damp cloth. You have now finished descaling the machine.

Please follow the instructions below or watch the video.

Place the water hardness sticker under water for 1 second.

The number of red squares indicates the water hardness level.

Switch the machine ON.

Press the Latte Macchiato and Warm Milk Froth buttons simultaneously for 3 seconds to enter Menu mode: Descaling and clean alerts will start blinking.

Touch in a single continuous movement the following buttons:
1. Latte Macchiato
2. Cappuccino
3. Warm Milk Froth
The current water hardness setting is indicated by the corresponding buttons (steady light).

Within 15 seconds, you can set the desired value by pressing the corresponding button. They will blink 3 times rapidly to confirm new settings.

The machine will exit out of menu mode automatically and will return to ready mode.

Switch the machine off.

Press the Latte Macchiato and Warm Milk Froth buttons simultaneously for 3 seconds to enter Menu mode: the Descaling and clean alerts will start blinking.

Touch in a single continuous movement the following buttons:
1. Ristretto
2. Espresso
3. Lungo
The current automatic power off setting is indicated by the corresponding buttons (steady light).

Activation power off mode after 8 hours. Press and hold both the Lungo and Espresso button and switch machine on.

The machine will exit out of menu mode automatically and will return to ready mode.